Results 1 to 5 of 5

Thread: How a Turbo System Works

  1. #1
    Boostaholic
    monjarassi's Avatar
    Join Date
    Apr 2011
    Location
    Houston TX
    Posts
    2,665
    Feedback Score
    2 (100%)

    How a Turbo System Works

    This will mainly be intended to out new members seeking to go Turbo or members joining the Turbo side from simply being SC or N20.

    Engine power is proportional to the amount of air and fuel that can get into the cylinders. All things being equal, larger engines flow more air and as such will produce more power. If we want our small engine to perform like a big engine, or simply make our bigger engine produce more power, our ultimate objective is to draw more air into the cylinder. By installing a turbocharger, the power and performance of an engine can be dramatically increased.

    So how does a turbocharger get more air into the engine?






    1 Compressor Inlet
    2 Compressor Discharge
    3 Charge air cooler (CAC)
    4 Intake Valve
    5 Exhaust Valve
    6 Turbine Inlet
    7 Turbine Discharge

    The components that make up a typical turbocharger system are:
    • The air filter (not shown) through which ambient air passes before entering the compressor (1)
    • The air is then compressed which raises the air’s density (mass / unit volume) (2)
    • Many turbocharged engines have a charge air cooler (aka intercooler) (3) that cools the compressed air to further increase its density and to increase resistance to detonation
    • After passing through the intake manifold (4), the air enters the engine’s cylinders, which contain a fixed volume. Since the air is at elevated density, each cylinder can draw in an increased mass flow rate of air. Higher air mass flow rate allows a higher fuel flow rate (with similar air/fuel ratio). Combusting more fuel results in more power being produced for a given size or displacement
    • After the fuel is burned in the cylinder it is exhausted during the cylinder’s exhaust stroke in to the exhaust manifold (5)
    • The high temperature gas then continues on to the turbine (6). The turbine creates backpressure on the engine which means engine exhaust pressure is higher than atmospheric pressure
    • A pressure and temperature drop occurs (expansion) across the turbine (7), which harnesses the exhaust gas’ energy to provide the power necessary to drive the compressor

    Which Turbocharger is Right for Me or more affectionately known as My Turbo & Me


    Selecting the proper turbocharger for your specific application requires many inputs. The primary input in determining which turbocharger is appropriate is to have a target horsepower in mind. This should be as realistic as possible for the application. Remember that engine power is generally proportional to air and fuel flow. Thus, once you have a target power level identified, you begin to hone in on the turbocharger size, which is highly dependent on airflow requirements.
    Other important factors include the type of application. An autocross car, for example, requires rapid boost response. A smaller turbocharger or smaller turbine housing would be most suitable for this application. While this will trade off ultimate power due to increased exhaust backpressure at higher engine speeds, boost response of the small turbo will be excellent.

    Alternatively, on a car dedicated to track days, peak horsepower is a higher priority than low-end torque. Plus, engine speeds tend to be consistently higher. Here, a larger turbocharger or turbine housing will provide reduced backpressure but less-immediate low-end response. This is a welcome tradeoff given the intended operating conditions.

    Selecting the turbocharger for your application goes beyond “how much boost” you want to run. Defining your target power level and the primary use for the application are the first steps in enabling your Garrett Performance Distributor to select the right turbocharger for you.


    Journal Bearings vs. Ball Bearings


    The journal bearing has long been the brawn of the turbocharger, however a ball-bearing cartridge is now an affordable technology advancement that provides significant performance improvements to the turbocharger.

    Ball bearing innovation began as a result of work with the Garrett Motorsports group for several racing series where it received the term the ‘cartridge ball bearing’. The cartridge is a single sleeve system that contains a set of angular contact ball bearings on either end, whereas the traditional bearing system contains a set of journal bearings and a thrust bearing


    Last edited by monjarassi; 11-27-2013 at 12:33 AM.
    Using promo code "SPOOLBUS" @ checkout when shopping in the eshop will save you money!!

  2.    Sponsored Links





  3. Become a Free Registered Member and Remove This Ad!


  4. #2
    Junior Member BuBBaSBuBBLE's Avatar
    Join Date
    Jul 2013
    Location
    Queens, NY
    Posts
    89
    Feedback Score
    0
    NICE write up!!!

  5. #3
    Boostaholic
    monjarassi's Avatar
    Join Date
    Apr 2011
    Location
    Houston TX
    Posts
    2,665
    Feedback Score
    2 (100%)
    Quote Originally Posted by BuBBaSBuBBLE View Post
    NICE write up!!!
    Using promo code "SPOOLBUS" @ checkout when shopping in the eshop will save you money!!

  6. #4
    Senior Member vdubkilla's Avatar
    Join Date
    Apr 2011
    Posts
    914
    Feedback Score
    0
    Good write up a few years ago when I went turbo I had no idea how the system worked all I knew is I was n/a and wanted to go faster !
    You and that bubble ain't nothin but trouble

  7. #5
    Boostaholic
    monjarassi's Avatar
    Join Date
    Apr 2011
    Location
    Houston TX
    Posts
    2,665
    Feedback Score
    2 (100%)
    added vid to 1st post
    Using promo code "SPOOLBUS" @ checkout when shopping in the eshop will save you money!!

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •