Page 2 of 3 FirstFirst ... 2 ... LastLast
Results 11 to 20 of 27

Thread: Locked in gear?

  1. #11
    Newbie thatSIfromthe845's Avatar
    Join Date
    Feb 2013
    Location
    Newburgh
    Age
    30
    Posts
    23
    Feedback Score
    0
    image.jpg so here's the slave cyl if you can't see it clearly I know I'm not a good photographer the left bolt isn't even there and the right one has the head sheered off

  2. #12
    BoostedK20.com Founder

    BoostedK20's Avatar
    Join Date
    Mar 2011
    Posts
    1,025
    Feedback Score
    1 (100%)
    Saw this on instagram last night - that is quite a predicament! Did you have both bolts in originally, or have you ever changed your slave/master cylinder? Anything you can think of that may have caused this?


    Need parts for your k-series setup? Check out our eShop! Click Here

    For all your eShop support needs:BoostedK20.com eShop Support Forum

  3. #13
    Newbie thatSIfromthe845's Avatar
    Join Date
    Feb 2013
    Location
    Newburgh
    Age
    30
    Posts
    23
    Feedback Score
    0
    I changed my slave over the summer sometime I had both bolts in snug. shortly after that was when my shift cable stretched smh lol. Maybe -20 degree temps plus innovative mounts was just too much vibration for the cold bolts.

    It's had the hybrid racing master setup for almost 2 years now so I doubt that did anything
    Last edited by thatSIfromthe845; 01-29-2014 at 12:14 PM.

  4. #14
    BoostedK20.com Founder

    BoostedK20's Avatar
    Join Date
    Mar 2011
    Posts
    1,025
    Feedback Score
    1 (100%)
    Quote Originally Posted by thatSIfromthe845 View Post
    I changed my slave over the summer sometime I had both bolts in snug. shortly after that was when my shift cable stretched smh lol. Maybe -20 degree temps plus innovative mounts was just too much vibration for the cold bolts.

    It's had the hybrid racing master setup for almost 2 years now so I doubt that did anything
    It's definitely possible. This time around, use Loctite!


    Need parts for your k-series setup? Check out our eShop! Click Here

    For all your eShop support needs:BoostedK20.com eShop Support Forum

  5. #15
    Formerly "Adm_rsx"


    PetefromtheStreets's Avatar
    Join Date
    Apr 2011
    Posts
    4,590
    Feedback Score
    1 (100%)
    In those temps anythings likely. Gears could have been worn from stresses you've out on them other days racing ect . and then we had cold temps here lately that didn't help the gears at all. Along with the upgraded clutch pressure. Snap bolts off or even broken a tooth

    s4 IG-petefromthestreets
    Cage plus radio member #1
    Tire slayer
    Breaking everything since 2011

  6. #16
    Newbie thatSIfromthe845's Avatar
    Join Date
    Feb 2013
    Location
    Newburgh
    Age
    30
    Posts
    23
    Feedback Score
    0
    yea I always plan for the worst when tearing my trans apart. even if it ends up being something simple i prefer to tear it all down to make sure everything else is perfect. as for the bolts snapping ive never seen that happen before but then again ive never seen my town ever hit -20 before either. so just little things so far i have to work today till 8pm so ill go back and tear the case off tonight and see what the inside is going to look like.

  7. #17
    BoostedK20.com Founder

    BoostedK20's Avatar
    Join Date
    Mar 2011
    Posts
    1,025
    Feedback Score
    1 (100%)
    Quote Originally Posted by thatSIfromthe845 View Post
    yea I always plan for the worst when tearing my trans apart. even if it ends up being something simple i prefer to tear it all down to make sure everything else is perfect. as for the bolts snapping ive never seen that happen before but then again ive never seen my town ever hit -20 before either. so just little things so far i have to work today till 8pm so ill go back and tear the case off tonight and see what the inside is going to look like.
    You should take pics when you mate the tranny back to the motor and make a DIY for us!


    Need parts for your k-series setup? Check out our eShop! Click Here

    For all your eShop support needs:BoostedK20.com eShop Support Forum

  8. #18
    Newbie thatSIfromthe845's Avatar
    Join Date
    Feb 2013
    Location
    Newburgh
    Age
    30
    Posts
    23
    Feedback Score
    0
    3/4th fork is demolished lol I pulled it all apart and forgot to take pics if I'm at my shop tomorrow I'll snap a picture. But I'm working 5am to 5pm so I doubt it. metal is everywhere and I got chips on multiple gears so this got even more interesting. If anyone knows a company that makes stronger forks definitely let me know

  9. #19
    Super Moderator
    Spaz's Avatar
    Join Date
    Mar 2011
    Posts
    1,687
    Feedback Score
    0
    I've never heard nor seen that before
    Available now are SPAZ APPROVED decals!!! Available in multiple colors!


    Need parts?! Check out our eShop and let me know! We can help you out!
    http://boostedk20.com/eshop/

  10. #20
    Formerly "Adm_rsx"


    PetefromtheStreets's Avatar
    Join Date
    Apr 2011
    Posts
    4,590
    Feedback Score
    1 (100%)
    Yea gonna need pics. I doubt the shift fork was the first thing to go. Not heard much issue besides worn or bent... Never broken. But geez.

    s4 IG-petefromthestreets
    Cage plus radio member #1
    Tire slayer
    Breaking everything since 2011

Page 2 of 3 FirstFirst ... 2 ... LastLast

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •